英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
notar查看　notar　在百度字典中的解释百度英翻中〔查看〕
notar查看　notar　在Google字典中的解释Google英翻中〔查看〕
notar查看　notar　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Pulse transformer reset current simulation in LTspice
    0 I am simulating the pulse transformer in LT spice to see how core gets reset using the diode D1 Diode D1 current (Id1 : red colour) is in pulsating form as shown in the image below But the magnetizing current (Il1 : blue colour) keeps on adding by each pulse and never returns to zero during off time of the pulse
  • LTspice -DC sweep and Transient analysis
    The system works fine and the V5 is 300 kHz pulse signal If I put DC sweep, the V5 source becomes 0 V so when I add transient at the same time to make V5 work, it cancels the DC sweep
  • LTSpice - How do we simulate pulses in RC circuits?
    The forth and fifth are rise and fall times, make these some small value such as 1n for sharp pulse edges, or if you know the rise and fall times you want set them to that The sixth is ON time, for a square wave this will be half of your pulse period, 0 1666 for 3 Hz Seventh is the period, 0 333 for 3 Hz
  • How to simulate an independent current source pulse in LTspice
    I am trying to simulate an independent current source pulse in LTspice but it is not behaving as expected I want the pulse to stay on for 10 ns but it just goes immediately on an off
  • LTspice Simulation not matching theory (CMOS implementation of a NOR . . .
    I've just began learning how to use LTspice and I started by trying a basic CMOS network for a NOR gate However, when I run the simulation i've got my "logic 0" as 3 72 V instead of f
  • simulation - How to use a parametric value within PULSE voltage source . . .
    I would like to use a parametric symbol for the period value of the PULSE component in LTSpice but so far I have been unsuccessful currently my source is: PULSE(-15 15 0 0 1e-6 0 1e-6 0 4e-6 1e-6
  • How to simulate sigma-delta ADC pulse train in LTspice
    I am trying to simulate a complete current sense path of a motor phase, right from the shunt resistor to the MCU in LTspice We are using an AMC1303 (50 mV differential)(MPN: AMC1303M0520DWV) sigma
  • LTSpice: Time varying voltage source parameters
    You can define an arbitrary waveform using a PWL source You just specify the time voltage points that you want the voltage to have You might also be able to achieve what you want using the two PULSE sources, each with a switch that is controlled by another pulse The switches would select which pulse source is active at any given time
  • Continuous measurement of pulse width or frequency in LTSPICE - . meas . . .
    I want to measure the pulse width of a series of non-deterministic square pulses (See Figure 1) In the end, I would have a vector of the duration of the n-occurrences vs time of occurrence Using
  • Generate PWM Signal in LTSpice - Electrical Engineering Stack Exchange
    If you need this to serve your previous question, you'll be needing a time-varying PWM You can set a ramp voltage in LTspice like this: PULSE(0 1 0 {0 99 f} {0 01 f} 0 {1 f}) which is a ramp from 0 to 1V, with period given by the frequency f You could have used {1 f} for rise time and zero for fall and Ton, but that setting can have adverse effects in the dynamic range in long runs Then





中文字典-英文字典  2005-2009