英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

catafalque    
n. 灵柩台,灵柩车

灵柩台,灵柩车

catafalque
n 1: a decorated bier on which a coffin rests in state during a
funeral

Catafalque \Cat"a*falque`\, n. [F., fr. It. catafalco, scaffold,
funeral canopy; of uncertain origin; cf. Sp. catafalso,
cadahalso, cadalso, Pr. casafalc, OF. chafaut. Cf.
{Scaffold}.]
A temporary structure sometimes used in the funeral
solemnities of eminent persons, for the public exhibition of
the remains, or their conveyance to the place of burial.
[1913 Webster]

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • LDP vs RSVP - Cisco Learning Network
    LDP is designed to be highly extensible, using TLV triplets to be able to transport multiple additional fields in the future and warrantee the compatibility with previous versions via ignoring the unknown new fields LDP is highly flexible, as supports local and remote neighbors (using targeted LDP sessions)
  • mpls ladp advertise-label for - Cisco Learning Network
    Normally, LDP advertises labels only for IP prefixes that are in the routing table You can use the mpls ldp advertise-labels interface command to force LDP to advertise a label for a prefix constructed from an interface address and a 32-bit mask
  • Chapter 5 - SRv6 | IPv6 Addressing - Cisco Learning Network
    Lab Diagram - Physical Interfaces This devices are configure with iosxrv-k9full-24 3 1 Lab Diagram - IPv4 addressing Topology XRv prompt and credentials IPv4
  • CCIEv5 MPLS (LDP,vrf lite,MPLS VPN) Study Guide
    OSPF LDP (LDP Autoconfig , MPLS LDP-IGP Synchronization) MPLS LDP Session Protection LDP Transport Address MPLS LDP Graceful Restart Feature VRF Lite (Multi-VRF CE) What is MPLS VPN Where MPLS LDP will be configured? How PE1 will recognize separate Different CE routes? Configuring vrf table and assign it to interface for IPv4 , IPv6
  • MPLS LDP Neighbor relationship not working - Cisco Learning Network
    I'm configuring ldp on my small network with 4 routers and im running an IGP on all the devices precisely OSPF in area 12, but when i issues the show mpls ldp neighbor command i dnt have any respond but if when using sh mpls interfaces is showing the interfaces are operational below is my config R1-R4 #conf t #ip cef #mpls label protocol ldp
  • VPLS fundamentals - Cisco Learning Network
    The split horizon rule assures that traffic received from the network won't be sent back to the network Control plane To provide VPLS service over the MPLS enabled network, the control plane must setup the bidirectional tunnels (2 unidirectional LSPs) between the PE devices using some label distribution protocol like LDP
  • Making sense of MP-BGP, LDP and IGP in an MPLS SP domain
    - LDP is required to automatically signal the LSP's based on the best next-hops calculated by the underlying IGP by advertising labels (based on next hops) to directly connected LDP neighbors throughout the MPLS domain of the Service Provider LDP advertises labels for every prefix in the routing table It is not based on next-hop
  • OSPF with VRF interface. - Cisco Learning Network
    router ospf 2 vrf 1 mpls ldp autoconfig network 155 1 0 0 0 0 255 255 area 0 interface Ethernet0 1 108 encapsulation dot1Q 108 ipvrf forwarding 1 ip address 155 1 108 8 255 255 255 0 Regards, Deepak Kumar Expand Post LikeLikedUnlike Samer I think what he meant is why would interface under VRF is enabled after enabling OSPF on global interfaces
  • IP OSPF NETWORK POINT-TO-POINT on LOOPBACK
    OSPF is advertising a mask of 32 This advertising conflicts with LDP, which uses configured masks If you go to the PE’s neighboring “P” router and do a “show mpls ldp binding 2 2 2 2 32” you won’t see anything, but if you do a “show mpls ldp binding 2 2 2 0 24” you will see en entry there
  • OSPF Loopback point-to-point - Cisco Learning Network
    Hi Guys! I am doing a OSPF lab and I have found out that there is a loopback interface configures as "point-to-point" which would be the goal to use "network point-to-point" under interface loopback? This command change the normal behaviour of the loopback interface? Thanks!





中文字典-英文字典  2005-2009